Installer guide

Monitor Setup

The installation should take 15-30 minutes with the basic tools outlined below. Do not attempt to splice or otherwise modify any equipment. Always follow caution when installing equipment that has electrical current and follow all appropriate safety standards. For assistance with any issues, please call (800) 218-4172 while onsite.

Need help on site?
(800) 218-4172

Call before leaving the site to validate the installation.

Parts Included in the Box

Pioneer Monitor Unit

Cellular and Bluetooth enabled monitoring device with pre-installed magnetic mounts.

Current Sensor

A split-core transformer that reads the current drawn by the motor and connects to the Pioneer Monitor Unit.

Cellular Antenna

An extended Antenna for connection to the Pioneer Monitor Unit.

Power Supply

For AC Power: An AC/DC Power Adaptor with a Multi-Conductor Cable with pre-crimped forks for connection to the terminals on one end, and a barrel-plug connector for connection to the Pioneer Monitoring Unit on the other.

For DC Power: A Multi-Conductor Cable with pre-crimped forks for connection to the Compactor Control terminals on one end, and a barrel-plug connector for connection to the Pioneer Monitoring Unit on the other.

Pickup Confirmation Beacon Optional

A magnetically mounted device installed on the Compactor Unit (self-contained compactor) or on the receiver box (Stationary Compactor) that will be transported from the client site to be emptied and will be returned to the same location.

Required Tools

An electric Drill with Phillips & Flat Head Bits OR both Medium Phillips & Flat Head Screwdrivers
A standard Voltmeter
An internet enabled smartphone used to access the mobile web application to take photographs of the device post-install.

Other Components Necessary for Installation

Control Panel
Control Panel Power Supply Transformer
Service Disconnect
Compactor

Status Indicator Lights

When powered, the Pioneer Monitor Unit will display its status using the LED light on the front of the device. The following table describes the status light color, pattern, and a description of what the color represents.

Color
Pattern
Description
Orange
Solid
Cellular Network is not accessible
Orange
Blinking
Connecting to Cellular Network
Green
Solid
Active and Healthy Cellular Network connection
Cyan (light blue)
Blinking
Pioneer Monitor Unit is reading data via Current Sensor
Blue
Slow Blinking
Pioneer Monitor Unit is preparing to send data
Blue
Solid
Pioneer Monitor successfully sent data (flashed for 1 sec)
Magenta
Blinking
Pioneer Monitor saved data locally, and will retry send
Red
Solid
Pioneer Monitor Unit failed to send data (flashed for 1 sec)

Installation Instructions

Before you begin, you will need to determine if inbound power supply is AC or DC, then follow the associated section below.

AC Power Supply Installation

1
Open the Control Panel.
2
Using a Volt Meter, identify a 110v-264v connection on the Control Panel’s Power Supply Transformer.
DO NOT PROCEED if you cannot identify a 110v-264v connection as you risk damaging the Pioneer Monitoring Unit. Call immediately for assistance (800) 218-4172
3
Turn the power OFF using the safety disconnect - Turn off power to the Compactor Control Panel before attempting to install, connect, disconnect or service the Current Sensor, Power Supply, or Current Sensor.
4
Connect Positive (WHITE) & Neutral (BLACK) wires of the Multi-Conductor Power Cable to the Control Panel Power Supply Transformer.
5
Plug the Multi-Conductor Power Cable into the AC-DC Power Adaptor, then plug the AC-DC Power Adaptor into the Pioneer Monitoring Unit using the integrated barrel-plug connector.
Continue to Unified Installation Instructions ↓

DC Power Supply Installation

1
Open the Control Panel.
2
Using a Voltmeter, identify a 5v-24v connection on the Control Panel Power Supply Transformer.
DO NOT PROCEED if you cannot identify a 5v-25v connection as you risk damaging the Pioneer Monitoring Unit. Call immediately for assistance (800) 218-4172.
3
Turn the power OFF using the safety disconnect - Turn off power to the Compactor Control Panel before attempting to install, connect, disconnect or service the Current Sensor, Power Supply, or Current Sensor.
4
Connect Positive (RED) & Neutral (BLACK) wires of the Multi-Conductor Power Cable to the Control Panel Power Supply Transformer.
5
Plug the Multi-Conductor Power Cable into the Pioneer Monitoring Unit using the integrated barrel-plug connector.
Continue to Unified Installation Instructions ↓

Unified Installation Instructions

1
Place magnetic base of Cellular Antenna onto the top of the Control Panel or any permanent, magnetic surface.
DO NOT PLACE ANTENNA ON ANY SURFARCE THAT WILL BE HAULED AWAY DURING SERVICE.
2
Wire the copper end of the Cellular Antenna through the bottom of the Control Panel.
3
Insert the Cellular Antenna’s copper male SMA connector into the Pioneer Monitor Unit’s copper female SMA. Tighten securely into place.
4
Clip the Current Sensor around ONE of the primary inbound power cables running into the Compactor’s electrical power system/motor starter inside the Control Panel. (a) If the Current Sensor has a directional arrow, ensure that arrow is pointing in the direction of electrical flow towards the Compactor, and not towards the inbound power source from the building/utility provider. (b) If a Phase Inverter is in use, place it on the cable before the inverter.
5
Insert the Current Sensor’s 3.5mm jack into the Pioneer Monitor Unit’s right port.
6
Place the Pioneer Monitor Unit securely INSIDE the Compactor Control Panel Box with the integrated magnetic mounts.
7
Turn the Service Disconnect back to “ON”.
8
Pioneer Monitor Unit LED Status Indicator should trigger – see Status Indicator Lights (refer to page 4 for a full list of Indicator Lights and their meaning) i. Note: (The Status Indicator may change to different colors during the initializing process. Process may take up to 5 minutes as the device registers with the cellular network.)
9
When the Status Indicator is a solid Green, the initializing process is complete, and the Monitor is ready for use.
10
Run the compactor and ensure the Cyan Recording Data Indicator, followed by Blue Sending Data to Server Indicator, both trigger.
11
If included, place the Pickup Confirmation Beacon directly onto the Compactor in a secure location where it is unlikely to be knocked off or removed during service.
12
PRIOR TO LEAVING THE SITE, call (800) 218-4172 to validate the installation with a member of the DSQ team and/or troubleshoot any issues. Payment may be withheld until this step has been completed.
13
Complete the Installation Checklist

Your next haul is already on the calendar. Find out if it needs to be.

Order DSQ Pioneer